Exactly How to Remove and Change a Bathtub

This Page

They are making a number of good annotation on A Step-by-Step Guide to Installing a Bathtub as a whole in the content directly below.


A Step-by-Step Guide to Installing a Bathtub
Setting up a bathtub isn't specifically brain surgery, but it does require strong plumbing, carpentry, and occasionally, tiling skills. Changing an old tub with a brand-new one is likewise a moderately tough project. If the old bathtub is conveniently easily accessible, the project can relocate quickly; if you have to open up a wall to get rid of the old tub as well as position the new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will need an assistant to vacate the old tub as well as embeded in the brand-new one. Make sure you have qualified yourself for the task and also fit attempting it. Instead of working with a contractor to take over a halfway-completed job, it is far better to think about utilizing one prior to you begin. Possibilities are you might require a professional plumber to make tube connections.
This write-up will certainly help you set up a brand-new bath tub in your bathroom if you have already acquired a brand-new tub as well as do not require to change the arrangement of your previous water system pipelines.
Your devices and also product checklist ought to make up the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipeline Caps


  • Getting ready for the Installment


    First of all, the sustaining framework provided with the bath ought to be fitted (if needed) according to the maker's guidelines. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is essential to make sure that if the faucet includes a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to avoid strain on the bathtub.
    Fit the adaptable faucet adapters to the bottom of both taps using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make sure you use all of the provided washing machines.
    Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should now prepare to be suited its last position.

    Removing Old Taps


    If you require to replace old taps with brand-new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, turn on the taps to drain pipes any water continuing to be in the system. The procedure of removing the existing faucets can be quite bothersome because of the restricted gain access to that is frequently the instance.
    Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will come from the pipes. As soon as the supply pipes have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from transforming throughout this process. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleaned up of any old securing substance.
    Before moving on to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.

    Setting up the Bathtub


    Using both wood boards under its feet, put the bathtub in the required placement. The wood boards are valuable in uniformly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto four small factors.
    The following goal is to ensure that the bath tub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bath tub up until the spirit level reviews level.
    To install faucets, fit the bottom of the furthest versatile faucet port to the proper supply pipe by making a compression join; after that do the exact same for the other tap.
    Activate the water as well as check all joints and new pipework for leaks and tighten them if essential. Load the tub and additionally inspect the overflow outlet and also the typical outlet for leakages.
    Ultimately, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bath tub must wait until the bath tub has been utilized at least when as this will settle it right into its final placement.

    Fitting New Touches


    If the tails of the new taps are plastic, after that you will require a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the tap as well as the other end supplies a connection to the current supply pipes.
    If you require to fit a monobloc, then you will certainly need lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
    Next, place the tap in the placing hole in the bath/basin guaranteeing that the washing machines are in location between the tap and also the sink. Protect the faucet in place with the maker provided backnut. When the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular faucet connectors. The previous type ought to be attached to the tap finishes initially, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.

    Tiling Around the Bath tub


    In the area where the bath fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to split an inflexible seal, causing the water to permeate the wall surface in between the bath as well as the tiling, bring about complications with dampness as well as feasible leakages to the ceiling listed below.
    You can choose from a range of coloured sealers to assimilate your components as well as installations. They are marketed in tubes and cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to enable the motion experienced when the tub is in use. The sealant can split relatively very early if you do not take into account this activity prior to sealing.
    Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise easily available on the market. It is recommended to fit the tiles using water-resistant or waterproof adhesive and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    A Step-by-Step Guide to Installing a Bathtub

    I'm certainly very interested in A Step-by-Step Guide to Installing a Bathtub and I'm hoping you appreciated the new entry. Please take a moment to distribute this article if you liked it. We appreciate reading our article about How to Install a Bathtub.




    This Site


    Leave a Reply

    Your email address will not be published. Required fields are marked *